It’a detained by magnets so it doesn’t get in the basket and interfere with spreading out the grounds. Needs a clean up with a lick of sandpaper, pretty stupid but these things cost like 50 bucks /shrug
EDIT: appreciate all the concern for my health, it touches dry coffee grounds. I agree that if it got wet there’d be health problems but unless it gets real humid there’s just no opportunity for decay. As for random leaching same diff, without heat and wet it’s not really a concern.
That said I probably will seal an improved design, this is just a test piece.
Please keep in mind that you need to seal that print before you use it with food. Because of the layers, there’s are a ton of places for dirt and bacteria to hide that are impossible to clean. Additionally, depending on what kind of nozzle you used, heavy metals can end up in your print which you don’t want to then leech into your coffee. General advice is to just not use 3d prints first good, but if you really want to you should coat them in a food safe epoxy before using.
This is good advice.
On the bright side for OP, his part should (hopefully) only come into contact with dry coffee grounds so some of those concerns are lessened.
In other applications – sealant or not – I can only imagine pouring hot coffee over a PLA part would not be a recipe for success…
I’ve been meaning to make one that molds to my grinder to prevent grinds flying all over the counter.
Just FYI, you can find metal dosing rings with magnets for as low as $3 on AliExpress. I’m sure yours fits better though!
Huh, didn’t consider aliexpress. I have an old lever machine with a non standard basket size (49 mm or something) so idk if they exist for it. I can see one with a brief search, but it protrudes down into the basket to locate itself which is a bit inelegant.
3D printed parts are NOT food safe.
In general, yes. But the contact here is minimal. I wouldn’t be worried.
I know it’s probably sacrilege, but I avoid the need for one of these by grinding half a dose, tamping a bit then grinding the rest and finishing the tamp. I’m using a Breville Barista Express so couldn’t (easily) use one of these even if I wanted to.
I’m curious how you retain the magnets in it? Are they printed in, or mechanically added later? (I know very little about 3d printing, this just came up in my top-6-hour feed)
I haven’t done much with magnets, but I saw one model where you pause the print halfway through, drop magnets into the holes, then continue the print and they get sealed in Amontillado-style.
Pop the magnets into the paused print.
The magnets: "Hahaha. This is a fine joke, good sir!’
Resume print
Magnets: “Yes, a very funny joke indeed. Wait, sir, where are you going! Sir! SIR!!”
Walk away knowing that neither you nor anyone else will see those magnets again
Oh God imagine being 3d printed alive into your casket
Worst part is it taking forever for it to print the casket around you, and you’re just lying there unable to do shit and just watch the casket close around you in ultra slow-mo. Like being buried alive with a tea-spoon for a shovel.
I’m not really a coffee wanker so I don’t know one way or the other what tamping halfway would do. I just want to be able to dump the grounds in, shake, and tamp.
The magnets are just push fit into little holes in the bottom. I just tap them in with blunt nail and a hammer.
So usually id agree that 3d prints shouldn’t be used for food, but this is a coffee hopper, they’re made from plastic already and I guarantee you the ones we used at Starbucks didn’t get that clean either, it’s fine, just sand it and get rid of those hairs
3d printing vs injection molding is a huge difference, so it’s not fair to say “they are both made of plastic”.
Yeah you need moisture for decay. Tiny fines might eventually go rancid in tiny pores and taste or smell a little bad but idk. She’ll be right.
Like it’s not like I clean the burrs that grind the beans much so if rotting was a problem I’d be dead already.
I use some supposedly food grade filament with a stainless nozzle and dedicated extruder, and after initial finishing they get a dip in food grade epoxy. I only made star wars and penis shaped cookie cutters though.
Microplastic speed run
He could just run a flame on it to melt whispy plastic strands down
Do you really thing that coffee grounds brushing up on something sheds significant amounts compared to like all the plastic you touch and then eat after not washing your hands? Or the Teflon in the rain on our crops? or storing food in plastic containers particularly during heating or freezing?
I’d be more concerned about takeway coming in shitty plastic containers that stain (indicating mixing on a molecular level) than coffee grounds touching a piece of PLA.
Yes, absolutely. Coffee grounds rubbing up against rough 3d printed plastic is going to act like little grinders pulling off bits of of plastic directly into the grounds.
Not to say that we all haven’t already lost the microplastics speed run. I am concerned about the things you listed, but yeah, I wouldn’t want anything 3d prone to be so close to so many small hard moving pieces of food.
3d printed plastic isn’t much worse than other plastic. The grinds aren’t under any force.
Have a look at a printed part under SEM and you’ll see it’s quite smooth and cohesive. Coffee grounds are light and fluffy, they don’t grind plastic.
I think you’re not basing this on any scientific investigation.
To each their own I suppose
Heads up, make sure you use food safe filament for this. And I would still be rather wary of excessive micro plastics in my morning brew
Pretty cool
You can find dosing funnels for ~$12 on Amazon. Still overpriced but eclipsed by the investment you made in the espresso machine.
